StanCraft 360 Hammerhead
2020 • 36' (10.97 m)
• Power
US
$995,000 USD
2020 StanCraft 360 Hammerhead with twin 6.2L ilmor V8 motors and joy stick controls. This has a custom stereo with upgraded speakers and subs that really get loud and sound amazing. Low hours on the motors.
Ready now for immediate delivery. Beat the one year wait for a new order
- Twin Ilmor 6.2 L V8 Engines 430hp each only 120 hours.
- Fresh Water Only boat so far. Never seen salt
Financing Available. World Wide Delivery Available.
Vessel Information
| Builder: | StanCraft |
|---|---|
| Model: | 360 Hammerhead |
| Model Year: | 2020 |
| Category: | Power |
| Sub Category: | Antique and Classics, Cruisers, Sports Cruiser |
| Condition: | Used |
| LOA: | 36' (10.97 m) |
|---|---|
| Engine Info: | Ilmoor 6.2L V8 Direct unleaded 430|horsepower Inboard 2020 120 Port |
| Location: | Hayden, ID US |
|---|---|
| City: | Hayden |
| Country: | US |
Steering System
Joystick Control
SKETCH RENDER AND DRAW TILL PERFECT
We love to draw, sketch, and render. This is really where we work our brains to get you the perfect StanCraft. Putting all our minds together to get a masterpiece. Without this your just buying another boat..
FINAL DRAWINGS
Once we have the design finished with the perfect rendering it's time to create the drawings. The blueprints for our builders.
TIME TO GET DUSTY
This is where the real fun starts! Whether you visit regularly to see progress or we email the photos weekly you get to watch the build step by step. A fascinating process that takes a pile of lumber and turns it into a dream.
FRAME IT UP
The builders will use the blueprints to cut the frames and attach them to the keel. Every piece is mechanically attached with a #10 stainless steel screw and bonded with a 5200 adhesive.
THE PLANKS
After it has been framed we start planking the hull. There are many ways to build a boat but for the past 83 years we have used the plank on frame process, it is a tried and true process and gives the hull an incredible amount of strength.
PLUGGING THE HOLES
When we are finished planking we plug all of the screw holes. We hand select the perfect plug for each hole making sure that the grains match and are facing the same direction. After each plug is carefully glued in place we sand them flush to the planks.
BUILDING THE DECK
Once the hull is completed it will move to our top side shop. This is where we finish all of the remaining wood work from the deck planking to the seat frames and floors.
UPHOLSTERY
StanCrafts are just as beautiful on the inside as the outside. Here we add those elegant features like mahogany decking, shelving, and more. We spend 100's of hours on the interior alone.
MAKE IT SHINE
Now that all of the woodwork is done we stain and varnish the boats. We apply 16 coats of varnish and buff it to a mirror finish.
RIGGING
While the finishing process is taking place we are also rigging the boat. In this stage we install all of the electrical components and pull hundreds of feet of wire through the boat as well as install the engine(s), drives, and fuel system.
TESTING, TESTING, AND MORE TESTING
No boat leaves before its time. We water test every boat for a minimum of 6 hours before it leaves for its new home. Systems are dialed, props are tuned, engines are perfect. Just turn the key and have a blast!
Disclaimer
The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice.